Pulp & Paper Mill in Indonesia. Approximate location -4.60454, 104.89801.
Pulp & Paper MillIndonesiaCO₂ reported
P.T. Pola Pulpindo Mantap is a pulp & paper mill in Indonesia with a reported capacity of 858,213 t of pulp & paper. It turns wood or recovered fibre into pulp and paper, with large steam and drying loads. By capacity it ranks #8 of 14 pulp & paper mills tracked in Indonesia. It emits about 463,799 tonnes of CO₂e per year (Climate TRACE) — roughly the tailpipe emissions of 108,112 cars.
Facility data: Climate TRACE v6 (asset-level capacity & CO₂e, CC BY 4.0), id ct-44375554.
在858,213 t of pulp & paper时，P.T. Pola Pulpindo Mantap是Indonesia中pulp & paper mill的中位数约 858,213 t of pulp & paper。 子部门：pulp-and-paper。 作为pulp & paper mill，它需要强烈的工艺热量（通常150–250°C）来进行其核心工业操作——必须通过锅炉、炉或直接燃烧供应的热量，通过未隔热的容器和管道的损失代表浪费的燃料。可拆卸模块化绝缘可以将这些损失减少80-96%，将表面冷却至≤45°C，投资回收期通常不到2年。 纸浆和造纸厂为制浆工艺和纸张干燥机发电自己的蒸汽，运行大型锅炉系统，其中热损失直接降低效率。
容量和CO₂强度比较从Climate TRACE工业设施数据计算得出；部门角色基于工程参考。
This facility's reported annual CO₂e in the everyday equivalents from the US EPA Greenhouse Gas Equivalencies calculator:
Equivalencies: US EPA Greenhouse Gas Equivalencies. Emissions: Climate TRACE.
Reported capacity (t of pulp & paper), Climate TRACE v6 (asset-level capacity & CO₂e, CC BY 4.0).
P.T. Pola Pulpindo Mantap sits in a tropical rainforest climate zone (Köppen Af), at 4.6°S in the southern hemisphere.
Köppen zone: Köppen-Geiger world climate classification (Kottek et al. 2006, 0.5° grid).
The #8 largest of 14 pulp & paper mills in Indonesia by reported capacity.
Coordinates -4.60454, 104.89801. View on OpenStreetMap.
A pulp & paper mill like this runs hot equipment that sheds heat continuously: digesters, dryers, evaporators, steam lines, hot-water systems (surface/process temperatures around 80–200 °C). These surfaces lose energy to the air year-round; removable modular insulation cuts that loss, brings outer surfaces to ≤45 °C, and unclips for inspection.
On an already-insulated site (pipes & valves in cladding / jackets), closing the remaining gaps, flanges and damaged sections and switching to removable covers indicatively recovers about 9,000 MWh/yr (≈ 1,800 t CO₂/yr) — scaled to this site's reported CO₂ within its sector. Bare or damaged surfaces recover several times more.
See Inzonex insulation → Estimate your site →
Indicative, not a measurement. Conservative floor for an already-insulated plant; a TIPCHECK on-site audit gives a measured figure. Industry context: EiiF TIPCHECK — industrial insulation can save ~14 Mtoe/yr in EU, payback typically <2 years.
Bare hot surfaces here exceed the touch-safe limit (EN ISO 13732-1); insulation to ≤45 °C is a worker-safety and compliance win. And before electrification, fuel-switching or CCS, eliminating surface heat loss is the cheapest, fastest, lowest-risk step — audit the bare spots first, rip-and-replace later.
Domestic energy-efficiency grants are limited here; industrial decarbonisation is mainly funded externally:
CBAM. Exporters of cement, steel, aluminium, fertiliser, hydrogen and electricity to the EU face the Carbon Border Adjustment Mechanism — cutting embedded emissions (efficiency + insulation) lowers the levy.
Routed via national development banks / accredited entities — not a direct factory grant. Verified 2026.
P.T. Pola Pulpindo Mantap is a pulp & paper mill in Indonesia. It turns wood or recovered fibre into pulp and paper, with large steam and drying loads.
P.T. Pola Pulpindo Mantap has a reported capacity of 858,213 t of pulp & paper.
P.T. Pola Pulpindo Mantap emits about 463,799 tonnes of CO₂e per year (Climate TRACE) — roughly the tailpipe emissions of 108,112 cars. That ranks #44 among tracked facilities in Indonesia.
P.T. Pola Pulpindo Mantap is in Indonesia, near coordinates -4.60454, 104.89801.
