Enueruforty Co.,Ltd.

Enueruforty Co.,Ltd. is a textile mill in Japan with a reported capacity of 24,062,284 USD. It spins, dyes and finishes textiles, leather or apparel using process steam. By capacity it ranks #63 of 64 textile mills tracked in Japan. It emits about 630 tonnes of CO₂e per year (Climate TRACE) — roughly the tailpipe emissions of 147 cars.

Facility data: Climate TRACE v6 (asset-level capacity & CO₂e, CC BY 4.0), id ct-38477267.

在上下文中：该设施如何比较

在24,062,284 USD时，Enueruforty Co.,Ltd.是Japan中textile mill的中位数约 24,062,284 USD。 子部门：textiles-leather-apparel。 作为textile mill，它需要强烈的工艺热量（通常60–150°C）来进行其核心工业操作——必须通过锅炉、炉或直接燃烧供应的热量，通过未隔热的容器和管道的损失代表浪费的燃料。可拆卸模块化绝缘可以将这些损失减少80-96%，将表面冷却至≤45°C，投资回收期通常不到2年。 纺织厂使用工艺蒸汽进行染色、整理和干燥，通常需要在长时间运行期间进行严格的温度控制——持续的热损失会侵蚀利润。

容量和CO₂强度比较从Climate TRACE工业设施数据计算得出；部门角色基于工程参考。

What 630 t CO₂e a year looks like

This facility's reported annual CO₂e in the everyday equivalents from the US EPA Greenhouse Gas Equivalencies calculator:

Equivalencies: US EPA Greenhouse Gas Equivalencies. Emissions: Climate TRACE.

Capacity vs largest textile mills in Japan

Reported capacity (USD), Climate TRACE v6 (asset-level capacity & CO₂e, CC BY 4.0).

Local climate

Enueruforty Co.,Ltd. sits in a temperate oceanic climate zone (Köppen Cfb), at 40.0°N in the northern hemisphere.

Köppen zone: Köppen-Geiger world climate classification (Kottek et al. 2006, 0.5° grid).

How it compares & nearby sites

The #63 largest of 64 textile mills in Japan by reported capacity.

Nearby industrial sites

• Hachinohe Cement Hachinohe Cement Plant · Cement Plant · 675,856 t CO₂
• Taiheiyo Cement Ofunato Cement Plant · Cement Plant · 761,740 t CO₂
• KHP Kitakami HiTec Paper Co. - Division of Mitsubishi Paper Mills Pulp Mill · Pulp & Paper Mill · 113,825 t CO₂
• Mitsubishi Materials Iwate Cement Plant · Cement Plant · 177,401 t CO₂

Location

Coordinates 40.04857, 141.86606. View on OpenStreetMap.

Heat loss & insulation profile

A textile mill like this runs hot equipment that sheds heat continuously: dyeing vessels, stenters/dryers, steam lines, hot-water & boiler house (surface/process temperatures around 80–200 °C). These surfaces lose energy to the air year-round; removable modular insulation cuts that loss, brings outer surfaces to ≤45 °C, and unclips for inspection.

effectively industrial laundries/dyeing - steam & hot water; 500-3000 MWh typical.

Indicative recoverable energy

On an already-insulated site (pipes & valves in cladding / jackets), closing the remaining gaps, flanges and damaged sections and switching to removable covers indicatively recovers about 620 MWh/yr (≈ 120 t CO₂/yr) — scaled to this site's reported CO₂ within its sector. Bare or damaged surfaces recover several times more.

See Inzonex insulation → Estimate your site →

Indicative, not a measurement. Conservative floor for an already-insulated plant; a TIPCHECK on-site audit gives a measured figure. Industry context: EiiF TIPCHECK — industrial insulation can save ~14 Mtoe/yr in EU, payback typically <2 years.

Safety & the no-regret first step

Bare hot surfaces here exceed the touch-safe limit (EN ISO 13732-1); insulation to ≤45 °C is a worker-safety and compliance win. And before electrification, fuel-switching or CCS, eliminating surface heat loss is the cheapest, fastest, lowest-risk step — audit the bare spots first, rip-and-replace later.

Japan: funding & obligation

Funding. Subsidies to cut upfront cost of energy-saving equipment for industry/commercial; some tied to 'specified business operator' status + S/A benchmark class.

Obligation. Factories/operators with large energy use are designated 'specified business operators': must appoint energy managers, report, and file mid-to-long-term efficiency plans. (applies as a rule above the stated threshold — we don't hold this site's metered energy use).

Verified 2026; confirm current scheme terms before applying.

Frequently asked questions