Hoorain Hi-Tech Fabrics Limited

Hoorain Hi-Tech Fabrics Limited is a textile mill in Bangladesh with a reported capacity of 24,937,949 USD. It spins, dyes and finishes textiles, leather or apparel using process steam. By capacity it ranks #1513 of 2,123 textile mills tracked in Bangladesh. It emits about 546 tonnes of CO₂e per year (Climate TRACE) — roughly the tailpipe emissions of 127 cars.

Facility data: Climate TRACE v6 (asset-level capacity & CO₂e, CC BY 4.0), id ct-38470058.

في السياق: كيف يتم مقارنة هذا المنشأة

عند 24,937,949 USD، يكون Hoorain Hi-Tech Fabrics Limited حوالي متوسط textile mill في Bangladesh (24,937,949 USD). القطاع الفرعي: textiles-leather-apparel. كـ textile mill، يتطلب حرارة عملية مكثفة (عادة 60–150°C) لعملياته الصناعية الأساسية — حرارة يجب توفيرها بواسطة الغلايات أو الأفران أو الاحتراق المباشر، والخسائر من خلال الحاويات والأنابيب غير المعزولة تمثل وقود مهدر. يمكن للعزل المعياري القابل للإزالة أن يقلل هذه الخسائر بمقدار 80-96٪، وتبريد الأسطح إلى ≤45°C، مع فترة استرجاع غالباً أقل من سنتين. تستخدم مصانع النسيج بخار العملية للصباغة والتشطيب والتجفيف، غالباً ما تتطلب تحكماً دقيقاً بدرجة الحرارة على فترات تشغيل طويلة — يؤدي فقدان الحرارة المستمر إلى تآكل الأرباح.

مقارنة السعة وكثافة CO₂ محسوبة من بيانات منشآت Climate TRACE الصناعية؛ دور القطاع بناءً على مرجع الهندسة.

What 546 t CO₂e a year looks like

This facility's reported annual CO₂e in the everyday equivalents from the US EPA Greenhouse Gas Equivalencies calculator:

Equivalencies: US EPA Greenhouse Gas Equivalencies. Emissions: Climate TRACE.

Capacity vs largest textile mills in Bangladesh

Reported capacity (USD), Climate TRACE v6 (asset-level capacity & CO₂e, CC BY 4.0).

Local climate

Hoorain Hi-Tech Fabrics Limited sits in a humid subtropical (dry winter) climate zone (Köppen Cwa), at 24.1°N in the northern hemisphere.

Köppen zone: Köppen-Geiger world climate classification (Kottek et al. 2006, 0.5° grid).

How it compares & nearby sites

The #1513 largest of 2123 textile mills in Bangladesh by reported capacity.

Nearby industrial sites

• Jamuna Spinning Mills Ltd. (Unit-02) · Textiles · 546 t CO₂
• Far East Spinning Industries Ltd · Textiles · 546 t CO₂
• Sm Spinning Mills Ltd. · Textiles · 546 t CO₂
• Safko Spinning Mills Ltd. · Textiles · 546 t CO₂
• Naheed Fine Tex Ltd · Textiles · 546 t CO₂
• Saiham Cotton Mills Ltd. · Textiles · 546 t CO₂

Location

Coordinates 24.14418, 91.32282. View on OpenStreetMap.

Heat loss & insulation profile

A textile mill like this runs hot equipment that sheds heat continuously: dyeing vessels, stenters/dryers, steam lines, hot-water & boiler house (surface/process temperatures around 80–200 °C). These surfaces lose energy to the air year-round; removable modular insulation cuts that loss, brings outer surfaces to ≤45 °C, and unclips for inspection.

effectively industrial laundries/dyeing - steam & hot water; 500-3000 MWh typical.

Indicative recoverable energy

On an already-insulated site (pipes & valves in cladding / jackets), closing the remaining gaps, flanges and damaged sections and switching to removable covers indicatively recovers about 590 MWh/yr (≈ 120 t CO₂/yr) — scaled to this site's reported CO₂ within its sector. Bare or damaged surfaces recover several times more.

See Inzonex insulation → Estimate your site →

Indicative, not a measurement. Conservative floor for an already-insulated plant; a TIPCHECK on-site audit gives a measured figure. Industry context: EiiF TIPCHECK — industrial insulation can save ~14 Mtoe/yr in EU, payback typically <2 years.

Safety & the no-regret first step

Bare hot surfaces here exceed the touch-safe limit (EN ISO 13732-1); insulation to ≤45 °C is a worker-safety and compliance win. And before electrification, fuel-switching or CCS, eliminating surface heat loss is the cheapest, fastest, lowest-risk step — audit the bare spots first, rip-and-replace later.

External climate finance your country can access

Domestic energy-efficiency grants are limited here; industrial decarbonisation is mainly funded externally:

• Japan JCM (Joint Crediting Mechanism) — Japan co-finances diffusion of decarbonising tech incl. INDUSTRIAL ENERGY EFFICIENCY in partner countries, in exchange for carbon credits. Channels: MOEJ model projects, ADB trust funds, NEDO demonstrations.
• UK International Climate Finance (ICF / ODA) — ~GBP 6bn ODA over 3 yrs; industrial-decarbonisation flows via Climate Investment Funds (CIF) - Clean Technology Fund.
• Green Climate Fund (GCF) + ADB / World Bank / UNIDO — Concessional finance & grants for industrial energy efficiency. E.g. GCF $200M ADB-led India Green Finance Facility; World Bank FP071 'Scaling Up Energy Efficiency for Industrial Enterprises in Vietnam'; ASEAN ACGF energy-efficiency revolving funds incl. SMEs.

CBAM. Exporters of cement, steel, aluminium, fertiliser, hydrogen and electricity to the EU face the Carbon Border Adjustment Mechanism — cutting embedded emissions (efficiency + insulation) lowers the levy.

Routed via national development banks / accredited entities — not a direct factory grant. Verified 2026.

Frequently asked questions