Industria De Calcados Wirth Ltda

Industria De Calcados Wirth Ltda is a textile mill in Brazil with a reported capacity of 19,302,191 USD. It spins, dyes and finishes textiles, leather or apparel using process steam. By capacity it ranks #974 of 1,732 textile mills tracked in Brazil. It emits about 302 tonnes of CO₂e per year (Climate TRACE) — roughly the tailpipe emissions of 70 cars.

Facility data: Climate TRACE v6 (asset-level capacity & CO₂e, CC BY 4.0), id ct-38473113.

У контексті: як порівнюється це підприємство

При потужності 19,302,191 USD Industria De Calcados Wirth Ltda — це приблизно медіана textile mill у Brazil (19,302,191 USD). Підсектор: textiles-leather-apparel. Як textile mill, воно вимагає високотемпературного технологічного тепла (зазвичай 60–150°C) для основних промислових операцій — тепла, яке повинне подаватися котлами, печами або прямим спаленням, і втрати через неізольовані судини та трубопроводи представляють витрачене напразно паливо. Знімна модульна теплоізоляція може зменшити ці втрати на 80–96%, охолодивши поверхню обладнання до ≤45°C, з окупністю часто менше 2 років. Текстильні фабрики використовують технологічну пару для фарбування, обробки та сушки, часто потребуючи суворого контролю температури протягом тривалих циклів — постійні втрати тепла знижують прибутковість.

Порівняння продуктивності та інтенсивності CO₂ розраховано на основі даних промислових об'єктів Climate TRACE; роль сектору заснована на інженерних довідниках.

What 302 t CO₂e a year looks like

This facility's reported annual CO₂e in the everyday equivalents from the US EPA Greenhouse Gas Equivalencies calculator:

Equivalencies: US EPA Greenhouse Gas Equivalencies. Emissions: Climate TRACE.

Capacity vs largest textile mills in Brazil

Reported capacity (USD), Climate TRACE v6 (asset-level capacity & CO₂e, CC BY 4.0).

Local climate

Industria De Calcados Wirth Ltda sits in a humid subtropical climate zone (Köppen Cfa), at 29.6°S in the southern hemisphere.

Köppen zone: Köppen-Geiger world climate classification (Kottek et al. 2006, 0.5° grid).

How it compares & nearby sites

The #974 largest of 1732 textile mills in Brazil by reported capacity.

Nearby industrial sites

• Industria, Comercio E Representacoes De Malhas Daiane Ltda · Textiles · 302 t CO₂
• Dass Nordeste Calçados E Artigos Esportivos Ltda · Textiles · 302 t CO₂
• Industria De Calcados West Coast Ltda · Textiles · 302 t CO₂
• Cpo - Curtume De Peles Ovinas · Textiles · 302 t CO₂
• Tre Anytry Beneficiamento De Peles Exóticas Ltda · Textiles · 302 t CO₂
• Emecelle Confecções Ltda · Textiles · 302 t CO₂

Location

Coordinates -29.59237, -51.10485. View on OpenStreetMap.

Heat loss & insulation profile

A textile mill like this runs hot equipment that sheds heat continuously: dyeing vessels, stenters/dryers, steam lines, hot-water & boiler house (surface/process temperatures around 80–200 °C). These surfaces lose energy to the air year-round; removable modular insulation cuts that loss, brings outer surfaces to ≤45 °C, and unclips for inspection.

effectively industrial laundries/dyeing - steam & hot water; 500-3000 MWh typical.

Indicative recoverable energy

On an already-insulated site (pipes & valves in cladding / jackets), closing the remaining gaps, flanges and damaged sections and switching to removable covers indicatively recovers about 500 MWh/yr (≈ 100 t CO₂/yr) — scaled to this site's reported CO₂ within its sector. Bare or damaged surfaces recover several times more.

See Inzonex insulation → Estimate your site →

Indicative, not a measurement. Conservative floor for an already-insulated plant; a TIPCHECK on-site audit gives a measured figure. Industry context: EiiF TIPCHECK — industrial insulation can save ~14 Mtoe/yr in EU, payback typically <2 years.

Safety & the no-regret first step

Bare hot surfaces here exceed the touch-safe limit (EN ISO 13732-1); insulation to ≤45 °C is a worker-safety and compliance win. And before electrification, fuel-switching or CCS, eliminating surface heat loss is the cheapest, fastest, lowest-risk step — audit the bare spots first, rip-and-replace later.

External climate finance your country can access

Domestic energy-efficiency grants are limited here; industrial decarbonisation is mainly funded externally:

• Japan JCM (Joint Crediting Mechanism) — Japan co-finances diffusion of decarbonising tech incl. INDUSTRIAL ENERGY EFFICIENCY in partner countries, in exchange for carbon credits. Channels: MOEJ model projects, ADB trust funds, NEDO demonstrations.
• UK International Climate Finance (ICF / ODA) — ~GBP 6bn ODA over 3 yrs; industrial-decarbonisation flows via Climate Investment Funds (CIF) - Clean Technology Fund.
• Green Climate Fund (GCF) + ADB / World Bank / UNIDO — Concessional finance & grants for industrial energy efficiency. E.g. GCF $200M ADB-led India Green Finance Facility; World Bank FP071 'Scaling Up Energy Efficiency for Industrial Enterprises in Vietnam'; ASEAN ACGF energy-efficiency revolving funds incl. SMEs.

CBAM. Exporters of cement, steel, aluminium, fertiliser, hydrogen and electricity to the EU face the Carbon Border Adjustment Mechanism — cutting embedded emissions (efficiency + insulation) lowers the levy.

Routed via national development banks / accredited entities — not a direct factory grant. Verified 2026.

Frequently asked questions